Controllers
Components
Downloads
Contact
Shows
9 Steps
Home
  • Home
  • Controllers
  • Components
  • Downloads
  • Contact
  • Shows
  • 9 Steps

TOSS Alloy-20® Straight
Impulse Heat Seal Band Selection

  • Sealing
  • Seal Cutting
  • Cutting

TOSS Alloy-20® Impulse Heatseal Bands are available in over 350 styles, shapes and sizes. Custom designed for any application, new or existing, TOSS Alloy-20 Impulse Heatseal Bands are longer lasting and provide for effective sealing at optimum speeds. TOSS’s Norex® Impulse Heat Seal Bands are ideal for sealing applications that require a minimal amount of heat seal band expansion.

Ideal impulse heat seal band selection is a function of many variables including material composition, material thickness, heat absorption of the jaw, and the nature of the cover strip used over the heat seal band. In general, the thicker the material to be sealed, the thicker the heat seal band that should be used. Most materials, 1 mil to 6 mil can be sealed efficiently with heat seal band in the thickness range of 0.1 mm to 0.25 mm. With very thick seals (multi-layers to totals of 15 mils or more) it may be well to use thicker bands or consider the possibility of applying heat from both sides.

Click here to see Contoured Bands

Click here to see Plating of Bands

Heat Seal Band Information


Sealing

Flat Band

The common Flat Band is an old stand-by configuration that was originally developed to make seals with widths wider than that which could be made with round wire. In most applications, the Flat Band has been replaced by the Tapered-edge Band or the Reflex Band. The Flat Band has the major disadvantage of sharp square edges that cut into and weaken the film along the edge of the seal. Failures of this kind are called “zipper failures”; the seal itself is well secured and appears good, but the package is dangerously weakened.

Tapered Edge Band

This band, usually called Tapered Band, is the contemporary version of the Flat Band. On this band the edges have been tapered down to a very thin edge. This produces two advantages. The tapering removes the sharp outer edge that cuts into the film while heating. It also acts to reduce the temperature of the band along its outer edges. Without a tapered edge the band will cut into the film along the edge of the seal and weaken the package.

Reflex Band

This is an excellent band for thick materials, hard to seal materials, and vacuum packaging. Because of the convex configuration of the band, it only makes edge contact with the underlayment backing. This limited contact minimizes heat loss and provides more energy for the sealing of the film. The Reflex Band is also excellent for liquid sealing because the convex face acts to squeeze the liquid out of the seal zone as the seal is made.

Double Seam Band

The Double Seam Band is used to make two perfectly parallel narrow seals. Double seams, although rarely needed, produce the impression of greater integrity. They are useful in sealing liquids or other hard to seal materials.


Seal Cutting

Beaded Band

This very popular band is used for cutting the film layers and concurrently sealing along both sides of the cut line. It is made with tapered edges as well and comes in a wide variety of sizes. The space behind the bead does not come in contact with the underlayment backing material. As a result heat is not lost from the beaded area; the bead becomes hotter than the adjacent edges, thereby, effecting a cutting action without overheating the sealed edges of the film.

T-Profile Band

This band, available in four (4) sizes, is made from solid extruded stock. It has a greater mass per unit of length than the Beaded Band and a sharper cutting edge. It is relieved in the back to minimize contact with its underlayment backing. This band retains its heat and is excellent for concurrently sealing and cutting multi-layers of film or thick film.

Custom Seal-Cut Band (CSC)

This special band is a combination of a Tapered Band and a Cutting Wire and is custom made to suit the specific needs of the application. The cut wire can be placed on the centerline of the band or along one edge, depending upon the desired result. (This technique of attaching a cutting wire can also be used on our TOSS custom contoured bands).

Trim Band

Not unlike the T-Profile band, the trim band is drawn from solid stock. Offered in three (3) different sizes its cutting edge is formed on the very edge of the band. This band functions well to seal and trim the edge of thicker materials or multi-layers of material where a sharper cutting action is desired.


Cutting

Half Round Wire

Half round wire is another variation on the round cutting wire. Though rarely used, it is available in two (2) sizes and function much the same as the oval wire except that it has a better cutting action than the Oval Profile Wire.

Cutting Wire

Round cutting wire is often used as an inexpensive means of cutting of polymer films, these wires are available in sizes from 0.3 mm to 1.2mm both in rolls and made up into pre-cut lengths with, or without, copper plating at the ends. As with bands, best performance it is obtained with brass end connectors brazed to the ends. When cutting through two or more layers, the layers of film will be sealed with a very narrow seal along the edge.

Oval Profile Wire

The Oval Profile Wire, available in two (2) sizes is larger in cross section than the round Cutting Wire. It is most useful for making narrow seals on thick or stacked materials. It is not very effective as a cutting wire.

Selection of the best Heatseal Band for any given application involves several considerations. The band must be of the correct width and configuration to produce the desired seal or cut/seal. In addition, the band must be thick enough (have sufficient mass) to store the heat energy required for delivery to the material being sealed. When creating an impulse seal, it is desirable to terminate the heating cycle as soon as possible and begin cooling. Remember, the seal is not finally made until the seal area is cool enough to be dimensionally stable. If the Heatseal Band is too thick or the heat energy delivered is too great, the cooling time will be prolonged, thus prolonging the total cycle and limiting production rate.

539 South Main Street, Nazareth, PA 18064 USA · Phone 610-759-8883 · Fax 610-759-1766

©2021 Toss Machine Components, Inc. All rights reserved.     Site Map